Search This Blog

Powered by Blogger.

Translate

[TC] Arduino Based Sunrise Alarm Clock

So We Want To Make Sunrise Alarm Clock Based On Arduino Board

Part List:
  1. Arduino
  2. Real Time Clock Module (http://www.sparkfun.com/products/99)
  3. 24xAssorted LEDs (In my case: 3UV, 2 Blue, 4 Red, 3 Yellow, 12 White)
  4. 24xResistors, 220ohm
  5. Solderless Breadboard
  6. Assorted wires
  7. 3x74HC595 shift registers
  8. A Shadow Display Box
  9. Frosting Spray
To put this thing together I used Elco's ShiftPWM Library to control the 24 LEDs. You could go bigger, but I wanted this to all fit into the box.
Personally, I had some PCBs from a previous project that I could fashion to make the LEDs easier to mount.
Everything is hooked up like in the schematic:

The "To SCL" and "To SDA" lines go to the Real Time Clock Module.
The parts are all mounted to the backing board of the shadow display box like so:

Load the program below in and you can set the time on the clock with the following command in serial monitor:
T(00-59)(00-59)(00-23)(1-7)(01-31)(01-12)(00-99)
T(sec)(min)(hour)(dayOfWeek)(dayOfMonth)(month)(year)
You can then set the alarm with a command:
A(00-59)(00-23)(0-1)(0-1)(0-1)(0-1)(0-1)(0-1)(0-1)
A(min)(hour)(sun)(mon)(tue)(wed)(the)(fri)(sat)
The alarm will attempt to be done with the cycle at the appropriate time set, so it will start with the UV LEDs and move through the progression fading the LEDs in and out as indicated in the arrays at the top of the program.

Arduino Code:

[TC] World’s smallest Bluetooth location ‘stickers’

World’s smallest Bluetooth location ‘stickers’ using Nordic Semiconductor SoCs



Nordic Semiconductor announced earlier that its SoC series nRF51822 has been specified into the world’s smallest Bluetooth low energy coin-sized location stickers, ‘StickNFind’ by Stick-N-Find Technologies. Using a free smartphone app, users can locate their stickers using a ‘radar screen’, set distance alerts called ‘virtual leash’, and do much more.
A system on a chip or system on chip is an integrated circuit that integrates all components of a computer or other electronic system into a single chip. It may contain digital, analog, mixed-signal, and often radio-frequency functions all of which would exist on a single chip substrate. A system-on-chip blurs the lines between chip design and system design.
World’s smallest Bluetooth location ‘stickers’
Ultra low power (ULP) RF specialist Nordic Semiconductor ASA announced earlier that its SoC series nRF51822 has been specified into the world’s smallest Bluetooth low energy coin-sized location stickers, ‘StickNFind’ by Stick-N-Find Technologies. StickNFinds are the size of a U.S. quarter at just 0.98-inch (24mm) in diameter and 0.16-inch (4mm) thick. Users can easily track up to twenty location stickers on a smartphone app. They can be used to track keys, remote controls, pets, and even people. Using a free smartphone app, users can locate their stickers using a ‘radar screen’, set distance alerts called ‘virtual leash’, and do much more.




StickNFind is offering developers a free software development kit (SDK) and technical support with its stickers already being developed for use in a wide range of applications including automated inventory tracking and monitoring within shops, stores, and shipping crates, plus security tracking of high value items such as precious stones and expensive tools or equipment.
The Nordic Semiconductor nRF51822
The Nordic Semiconductor nRF51822 is a multi-protocol Bluetooth low energy / 2.4GHz proprietary RF Flash-based SoC that is designed specifically to be used as a single-chip solution for a range of Bluetooth low energy and 2.4GHz proprietary designs in cost, power, and size constrained applications including PC peripherals, connected TV remote controls, sports/fitness/healthcare sensors, toys, and automation.
Key features of the IC include:
It has a 256 kB on-chip Flash and 16 kB RAM with a wide range of digital and mixed signal peripherals including SPI, 2-wire, ADC, and a quadrature decoder. The IC comes with 16 PPI channels, an on-chip LDO and an On-chip drop down DC/DC converter for 3V batteries such as coin cells. A +/- 250 ppm 32kHZ RC oscillator enables the implementation of Bluetooth low energy applications without an external 32kHz crystal thus saving cost and board space along with a 6x6mm 48-pin QFN package with up to 32 GPIOs.
The S110 Bluetooth low energy stack
The S110 Bluetooth low energy stack for the nRF51822 is provided as a downloadable, royalty-free, pre-compiled binary that can be programmed and updated separately.
The Key features of the stack include:
It has an asynchronous and event driven SVC-based API with run-time protection, GATT, GAP and L2CAP level APIs, peripheral and broadcaster roles and GATT client and server. It operates with a non-concurrent multi-protocol operation with a 2.4 GHz RF proprietary protocols while requiring less than 128 kB code space and 6 kB of RAM, leaving more that 128 kB flash and 10 kB RAM for application code. When compared to two-chip implementations using Nordic’s previous generation nRF8001 the nRF51822, running the S110 stack slashes power consumption by up to 50 per cent.
The S110 stack and the nRF51822 are complemented by the nRF518 SDK that includes a comprehensive set of Bluetooth low energy profiles, services, and example applications. For proprietary applications, the nRF51822 is complemented by a new and improved Gazell 2.4GHz RF protocol stack providing interoperability with nRF24L Series Gazell-based applications. The combination of the nRF51822 and the new Gazell protocol stack slashes power consumption by up to 30 per cent compared to Nordic’s previous generation nRF24LE1

MultiPurpose Robot For Shopping Mall

I Have My BE Final Year Project In Electronics and Telecommunications Engineering Named "MultiPurpose Robot For Shopping Mall" Which Includes "Camera For Video Surveillance + Fire FIghting + Robotic Arm For Pick And Place Purpose + Floor Cleaning

I Have Included Blackbook Copy....













Copyrights : Todayscircuits.blogspot.com If You Are Sharing Please Do Not Forget To Include 
[Today's Circuits]

[TC] 20 Arduino projects of 2012

While looking for ideas for new some new project I noticed there aren’t many lists of Arduino projects online so I decided to make one and in the last few days I’ve been carefully digging Reddit (r/Arduino) and the Arduino forum until I ended up with a list of 20 Arduino projects.
All the projects in this list follow two simple criteria:
  1. They’ve been published/released in 2012.
  2. They provide quite detailed info (the more the better).
The second criteria forced me to discard some amazing projects, but I didn’t want this post to be a simple showcase of cool Arduino projects, I wanted it to be an useful reference for Arduino users.

20. arduino-l3dgecomm

arduino-l3dgecomm
This project aims to integrate a 3D world with real sensors and motors, more a proof of concept than a proper project, but still an interesting idea. Project page.

19. Charlieplexed ATTiny LED Christmas Ornament

Charlieplexed ATTiny LED Christmas Ornament
A custom PCB designed in the shape of a Christmas tree, an Atmel ATTiny45 microcontroller, 5 IO pins, and 20 LEDs make a perfect Christmas ornament. Project page.

18. Sound Alarm

Sound Alarm
A simple idea, but it comes with quite few interesting features. The device built in this project is a sound level detector which sets off an “alarm” via IR when it detects the sound level is to high for too long. Project page.

17. Sleepy Timer

Sleepy Timer
SleepyTimer is an Arduino-based sleep monitor which uses a 3-axis IMU to infer nightly sleep patterns. It graphs the results on an LCD and on a thermal-transfer printer. Project page.

16. Polar Plotter

Polar PlotterA polar plotter is a plotter with a rotating, extendable arm. The construction is powered by an Arduino Uno and Maker Beams. Project page.

15. Lite Brite LED clock

Lite Brite LED clock
An instructable that shows you how to make a Lite Brite clock using a Lite Brite, an Arduino, 46 LED’s and a few other miscellaneous parts. Project page.

14. Game Controller

Arduino game controllerA game controller powered by a Teensy microcontroller. No project page, but a photo gallery and the source code are available.

13. MP3 Player

Arduino MP3 Player
Mix an Arduino Mega, an MP3 decoder, an SD card, and a nokia LCD with thousand lines of code and you’ll get a working MP3 player. Project overview.

12. Recognizing token image with camera

Recognizing Token Image With Camera
Devices built using LEGO always have something special… this one uses an Arduino Nano and an old webcam to recognize digits from a security code. Project page.

11. Reddit message indicator

Reddit message indicator
This project could be useful to all the Reddit users, it’s a small desk notifier that lights up when your Reddit account receives a message. Project page.

10. PIP-Boy

Fallout PIP-Boy
A PIP-Boy is a device used by the protagonist in the popular Fallout series of video games for navigation, radiation detection, data storage/playback, and inventory management. This instructable explains how to make one. Project page.

9. WiiChuck steered laser pointer

winchuck_laser_pointerThis project uses a Wii Nunchuck to control a laser pointer moved by 2 mini servos. Project page.

8. RCArduino Yaw Control

RCArduino Yaw Control
The aim of this project is to make race RC cars more stable and easy to drive especially for beginner drivers. Project pages 1 and 2.

7. Disco Planet

Disco Planet
 A huge disco ball made of 800 LEDs. Project Page.

6. Hacking hotel room locks

Hacking hotel room locks
Last summer a black hat called Cody Brocious (aka Daeken) managed to gain access to 4 million hotel rooms with Arduino board. Probably not an usual project, but it definitely deserved a place in this list! Paper and PDF slides available online.

5. Hidden light control

Hidden light control
Controlling a LED strip with an action figure of Ezio Auditore (Assassin Creed) is pretty cool, isn’t it? Project page.

4. ExpeditInvaders

ExpeditInvaders — the spiced up IKEA shelf
A simple bookshelf can be strongly enhanced by some LED modules controlled by an Arduino board. Project page.

3. Pumpktris

Pumpktris
The perfect project for Halloween: combining a pumpkin with the classic video game Tetris!Project page.

2. The Inebriator

inebriatorAn Arduino powered cocktail machine, with plenty of cocktails to choose from. Project website.

1. Pinokio

Pinokio
Pinokio is not just a lamp, it’s a beautiful animatronic powered by Arduino, Processing and OpenCV, which is aware of the environment around and expresses different behaviours in an incredibly natural way. Project log and in-action video.

Bonus project of 2012: Arduino cake

OLYMPUS DIGITAL CAMERAA lucky guy got this from his mum on his 18th birthday, unfortunately no schematic or sketch code are available, but you can check his forum post and maybe ask him for the recipe. :)
And that’s all for this list of 20 Arduino projects of 2012!
What’s your favourite one? Can you suggest any other awesome project? Just leave a comment below

How to build Digital Electronic Lock

Circuit

Digital Electronic Lock

Description

The digital lock shown below uses 4 common logic ICs to allow controlling a relay by entering a 4 digit number on a keypad. The first 4 outputs from the CD4017 decade counter (pins 3,2,4,7) are gated together with 4 digits from a keypad so that as the keys are depressed in the correct order, the counter will advance. As each correct key is pressed, a low level appears at the output of the dual NAND gate producing a high level at the output of the 8 input NAND at pin 13. The momentary high level from pin 13 activates a one shot circuit which applies an approximate 80 millisecond positive going pulse to the clock line (pin 14) of the decade counter which advances it one count on the rising edge. A second monostable, one shot circuit is used to generate an approximate 40 millisecond positive going pulse which is applied to the common point of the keypad so that the appropriate NAND gate will see two logic high levels when the correct key is pressed (one from the counter and the other from the key). The inverted clock pulse (negative going) at pin 12 of the 74C14 and the positive going keypad pulse at pin 6 are gated together using two diodes as an AND gate (shown in lower right corner). The output at the junction of the diodes will be positive in the event a wrong key is pressed and will reset the counter. When a correct key is pressed, outputs will be present from both monostable circuits (clock and keypad) causing the reset line to remain low and allowing the counter to advance. However, since the keypad pulse begins slightly before the clock, a 0.1uF capacitor is connected to the reset line to delay the reset until the inverted clock arrives. The values are not critical and various other timing schemes could be used but the clock signal should be slightly longer than the keypad pulse so that the clock signal can mask out the keypad and avoid resetting the counter in the event the clock pulse ends before the keypad pulse. The fifth output of the counter is on pin 10, so that after four correct key entries have been made, pin 10 will move to a high level and can be used to activate a relay, illuminate an LED, ect. At this point, the lock can be reset simply by pressing any key. The circuit can be extended with additional gates (one more CD4011) to accept up to a 8 digit code. The 4017 counting order is 3 2 4 7 10 1 5 6 9 11 so that the first 8 outputs are connected to the NAND gates and pin 9 would be used to drive the relay or light. The 4 additional NAND gate outputs would connect to the 4 remaining inputs of the CD4068 (pins 9,10,11,12). The circuit will operate from 3 to 12 volts on 4000 series CMOS but only 6 volts or less if 74HC parts are used. The circuit draws very little current (about 165 microamps) so it could be powered for several months on 4 AA batteries assuming only intermittent use of the relay.




Augmented Reality in a Contact Lens

Image: Raygun Studio
Image: Raygun Studio
The human eye is a perceptual powerhouse. It can see millions of colors, adjust easily to shifting light conditions, and transmit information to the brain at a rate exceeding that of a high-speed Internet connection.
But why stop there?
In the Terminator movies, Arnold Schwarzenegger’s character sees the world with data superimposed on his visual field—virtual captions that enhance the cyborg’s scan of a scene. In stories by the science fiction author Vernor Vinge, characters rely on electronic contact lenses, rather than smartphones or brain implants, for seamless access to information that appears right before their eyes.
These visions (if I may) might seem far-fetched, but a contact lens with simple built-in electronics is already within reach; in fact, my students and I are already producing such devices in small numbers in my laboratory at the University of Washington, in Seattle [see sidebar, "A Twinkle in the Eye"]. These lenses don’t give us the vision of an eagle or the benefit of running subtitles on our surroundings yet. But we have built a lens with one LED, which we’ve powered wirelessly with RF. What we’ve done so far barely hints at what will soon be possible with this technology.
Conventional contact lenses are polymers formed in specific shapes to correct faulty vision. To turn such a lens into a functional system, we integrate control circuits, communication circuits, and miniature antennas into the lens using custom-built optoelectronic components. Those components will eventually include hundreds of LEDs, which will form images in front of the eye, such as words, charts, and photographs. Much of the hardware is semitransparent so that wearers can navigate their surroundings without crashing into them or becoming disoriented. In all likelihood, a separate, portable device will relay displayable information to the lens’s control circuit, which will operate the optoelectronics in the lens.
These lenses don’t need to be very complex to be useful. Even a lens with a single pixel could aid people with impaired hearing or be incorporated as an indicator into computer games. With more colors and resolution, the repertoire could be expanded to include displaying text, translating speech into captions in real time, or offering visual cues from a navigation system. With basic image processing and Internet access, a contact-lens display could unlock whole new worlds of visual information, unfettered by the constraints of a physical display.
Besides visual enhancement, noninvasive monitoring of the wearer’s biomarkers and health indicators could be a huge future market. We’ve built several simple sensors that can detect the concentration of a molecule, such as glucose. Sensors built onto lenses would let diabetic wearers keep tabs on blood-sugar levels without needing to prick a finger. The glucose detectors we’re evaluating now are a mere glimmer of what will be possible in the next 5 to 10 years. Contact lenses are worn daily by more than a hundred million people, and they are one of the only disposable, mass-market products that remain in contact, through fluids, with the interior of the body for an extended period of time. When you get a blood test, your doctor is probably measuring many of the same biomarkers that are found in the live cells on the surface of your eye—and in concentrations that correlate closely with the levels in your bloodstream. An appropriately configured contact lens could monitor cholesterol, sodium, and potassium levels, to name a few potential targets. Coupled with a wireless data transmitter, the lens could relay information to medics or nurses instantly, without needles or laboratory chemistry, and with a much lower chance of mix-ups.
Three fundamental challenges stand in the way of building a multipurpose contact lens. First, the processes for making many of the lens’s parts and subsystems are incompatible with one another and with the fragile polymer of the lens. To get around this problem, my colleagues and I make all our devices from scratch. To fabricate the components for silicon circuits and LEDs, we use high temperatures and corrosive chemicals, which means we can’t manufacture them directly onto a lens. That leads to the second challenge, which is that all the key components of the lens need to be miniaturized and integrated onto about 1.5 square centimeters of a flexible, transparent polymer. We haven’t fully solved that problem yet, but we have so far developed our own specialized assembly process, which enables us to integrate several different kinds of components onto a lens. Last but not least, the whole contraption needs to be completely safe for the eye. Take an LED, for example. Most red LEDs are made of aluminum gallium arsenide, which is toxic. So before an LED can go into the eye, it must be enveloped in a biocompatible substance.
So far, besides our glucose monitor, we’ve been able to batch-fabricate a few other nanoscale biosensors that respond to a target molecule with an electrical signal; we’ve also made several microscale components, including single-crystal silicon transistors, radio chips, antennas, diffusion resistors, LEDs, and silicon photodetectors. We’ve constructed all the micrometer-scale metal interconnects necessary to form a circuit on a contact lens. We’ve also shown that these microcomponents can be integrated through a self-assembly process onto other unconventional substrates, such as thin, flexible transparent plastics or glass. We’ve fabricated prototype lenses with an LED, a small radio chip, and an antenna, and we’ve transmitted energy to the lens wirelessly, lighting the LED. To demonstrate that the lenses can be safe, we encapsulated them in a biocompatible polymer and successfully tested them in trials with live rabbits.
Photos: University of Washington
Photos: University of Washington
Second Sight: In recent trials, rabbits wore lenses containing metal circuit structures for 20 minutes at a time with no adverse effects.
Seeing the light—LED light—is a reasonable accomplishment. But seeing something useful through the lens is clearly the ultimate goal. Fortunately, the human eye is an extremely sensitive photodetector. At high noon on a cloudless day, lots of light streams through your pupil, and the world appears bright indeed. But the eye doesn’t need all that optical power—it can perceive images with only a few microwatts of optical power passing through its lens. An LCD computer screen is similarly wasteful. It sends out a lot of photons, but only a small fraction of them enter your eye and hit the retina to form an image. But when the display is directly over your cornea, every photon generated by the display helps form the image.
The beauty of this approach is obvious: With the light coming from a lens on your pupil rather than from an external source, you need much less power to form an image. But how to get light from a lens? We’ve considered two basic approaches. One option is to build into the lens a display based on an array of LED pixels; we call this an active display. An alternative is to use passive pixels that merely modulate incoming light rather than producing their own. Basically, they construct an image by changing their color and transparency in reaction to a light source. (They’re similar to LCDs, in which tiny liquid-crystal ”shutters” block or transmit white light through a red, green, or blue filter.) For passive pixels on a functional contact lens, the light source would be the environment. The colors wouldn’t be as precise as with a white-backlit LCD, but the images could be quite sharp and finely resolved.
We’ve mainly pursued the active approach and have produced lenses that can accommodate an 8-by-8 array of LEDs. For now, active pixels are easier to attach to lenses. But using passive pixels would significantly reduce the contact’s overall power needs—if we can figure out how to make the pixels smaller, higher in contrast, and capable of reacting quickly to external signals.
By now you’re probably wondering how a person wearing one of our contact lenses would be able to focus on an image generated on the surface of the eye. After all, a normal and healthy eye cannot focus on objects that are fewer than 10 centimeters from the corneal surface. The LEDs by themselves merely produce a fuzzy splotch of color in the wearer’s field of vision. Somehow the image must be pushed away from the cornea. One way to do that is to employ an array of even smaller lenses placed on the surface of the contact lens. Arrays of such microlenses have been used in the past to focus lasers and, in photolithography, to draw patterns of light on a photoresist. On a contact lens, each pixel or small group of pixels would be assigned to a microlens placed between the eye and the pixels. Spacing a pixel and a microlens 360 micrometers apart would be enough to push back the virtual image and let the eye focus on it easily. To the wearer, the image would seem to hang in space about half a meter away, depending on the microlens.
Another way to make sharp images is to use a scanning microlaser or an array of microlasers. Laser beams diverge much less than LED light does, so they would produce a sharper image. A kind of actuated mirror would scan the beams from a red, a green, and a blue laser to generate an image. The resolution of the image would be limited primarily by the narrowness of the beams, and the lasers would obviously have to be extremely small, which would be a substantial challenge. However, using lasers would ensure that the image is in focus at all times and eliminate the need for microlenses.
Whether we use LEDs or lasers for our display, the area available for optoelectronics on the surface of the contact is really small: roughly 1.2 millimeters in diameter. The display must also be semitransparent, so that wearers can still see their surroundings. Those are tough but not impossible requirements. The LED chips we’ve built so far are 300 µm in diameter, and the light-emitting zone on each chip is a 60-µm-wide ring with a radius of 112 µm. We’re trying to reduce that by an order of magnitude. Our goal is an array of 3600 10-µm-wide pixels spaced 10 µm apart.
One other difficulty in putting a display on the eye is keeping it from moving around relative to the pupil. Normal contact lenses that correct for astigmatism are weighted on the bottom to maintain a specific orientation, give or take a few degrees. I figure the same technique could keep a display from tilting (unless the wearer blinked too often!).
Like all mobile electronics, these lenses must be powered by suitable sources, but among the options, none are particularly attractive. The space constraints are acute. For example, batteries are hard to miniaturize to this extent, require recharging, and raise the specter of, say, lithium ions floating around in the eye after an accident. A better strategy is gathering inertial power from the environment, by converting ambient vibrations into energy or by receiving solar or RF power. Most inertial power scavenging designs have unacceptably low power output, so we have focused on powering our lenses with solar or RF energy.
Let’s assume that 1 square centimeter of lens area is dedicated to power generation, and let’s say we devote the space to solar cells. Almost 300 microwatts of incoming power would be available indoors, with potentially much more available outdoors. At a conversion efficiency of 10 percent, these figures would translate to 30 µW of available electrical power, if all the subsystems of the contact lens were run indoors.
Collecting RF energy from a source in the user’s pocket would improve the numbers slightly. In this setup, the lens area would hold antennas rather than photovoltaic cells. The antennas’ output would be limited by the field strengths permitted at various frequencies. In the microwave bands between 1.5 gigahertz and 100 GHz, the exposure level considered safe for humans is 1 milliwatt per square centimeter. For our prototypes, we have fabricated the first generation of antennas that can transmit in the 900-megahertz to 6-GHz range, and we’re working on higher-efficiency versions. So from that one square centimeter of lens real estate, we should be able to extract at least 100 µW, depending on the efficiency of the antenna and the conversion circuit.
Having made all these subsystems work, the final challenge is making them all fit on the same tiny polymer disc. Recall the pieces that we need to cram onto a lens: metal microstructures to form antennas; compound semiconductors to make optoelectronic devices; advanced complementary metal-oxide-semiconductor silicon circuits for low-power control and RF telecommunication; microelectromechanical system (MEMS) transducers and resonators to tune the frequencies of the RF communication; and surface sensors that are reactive with the biochemical environment.
The semiconductor fabrication processes we’d typically use to make most of these components won’t work because they are both thermally and chemically incompatible with the flexible polymer substrate of the contact lens. To get around this problem, we independently fabricate most of the microcomponents on silicon-on-insulator wafers, and we fabricate the LEDs and some of the biosensors on other substrates. Each part has metal interconnects and is etched into a unique shape. The end yield is a collection of powder-fine parts that we then embed in the lens.
We start by preparing the substrate that will hold the microcomponents, a 100-µm-thick slice of polyethylene terephthalate. The substrate has photolithographically defined metal interconnect lines and binding sites. These binding sites are tiny wells, about 10 µm deep, where electrical connections will be made between components and the template. At the bottom of each well is a minuscule pool of a low-melting-point alloy that will later join together two interconnects in what amounts to micrometer-scale soldering.
We then submerge the plastic lens substrate in a liquid medium and flow the collection of microcomponents over it. The binding sites are cut to match the geometries of the individual parts so that a triangular component finds a triangular well, a circular part falls into a circular well, and so on. When a piece falls into its complementary well, a small metal pad on the surface of the component comes in contact with the alloy at the bottom of the well, causing a capillary force that lodges the component in place. After all the parts have found their slots, we drop the temperature to solidify the alloy. This step locks in the mechanical and electrical contact between the components, the interconnects, and the substrate.
The next step is to ensure that all the potentially harmful components that we’ve just assembled are completely safe and comfortable to wear. The lenses we’ve been developing resemble existing gas-permeable contacts with small patches of a slightly less breathable material that wraps around the electronic components. We’ve been encapsulating the functional parts with poly(methyl methacrylate), the polymer used to make earlier generations of contact lenses. Then there’s the question of the interaction of heat and light with the eye. Not only must the system’s power consumption be very low for the sake of the energy budget, it must also avoid generating enough heat to damage the eye, so the temperature must remain below 45 °C. We have yet to investigate this concern fully, but our preliminary analyses suggest that heat shouldn’t be a big problem.
eye04
Photos: University of Washington
In Focus: One lens prototype [left] has several interconnects, single-crystal silicon components, and compound-semiconductor components embedded within. Another sample lens [right] contains a radio chip, an antenna, and a red LED.
All the basic technologies needed to build functional contact lenses are in place. We’ve tested our first few prototypes on animals, proving that the platform can be safe. What we need to do now is show all the subsystems working together, shrink some of the components even more, and extend the RF power harvesting to higher efficiencies and to distances greater than the few centimeters we have now. We also need to build a companion device that would do all the necessary computing or image processing to truly prove that the system can form images on demand. We’re starting with a simple product, a contact lens with a single light source, and we aim to work up to more sophisticated lenses that can superimpose computer-generated high-resolution color graphics on a user’s real field of vision.
The true promise of this research is not just the actual system we end up making, whether it’s a display, a biosensor, or both. We already see a future in which the humble contact lens becomes a real platform, like the iPhone is today, with lots of developers contributing their ideas and inventions. As far as we’re concerned, the possibilities extend as far as the eye can see, and beyond.
The author would like to thank his past and present students and collaborators, especially Brian Otis, Desney Tan, and Tueng Shen, for their contributions to this research.

About the Author

Babak A. Parviz wakes up every morning and sticks a small piece of polymer in each eye. So it was only a matter of time before this bionanotechnology expert at the University of Washington, in Seattle, imagined contact lenses with built-in circuits and LEDs. “It’s really fun to hook things up and see how they might work,” he says. In “For Your Eye Only”, Parviz previews a contact lens for the 21st century.

To Probe Further

You can find details about the fabrication process using self-assembly in “Self-Assembled Single-Crystal Silicon Circuits on Plastic,” by Sean A. Stauth and Babak A. Parviz, in Proceedings of the National Academy of Sciences, 19 September 2006.

Page Rank

google pagerank

Write For Us

Submit a Guest Post

Find us on Facebook

Categories

555 Timer IC 7 segment Display 8051 Project AC Circuits Adafruit Alarms Amplifier Circuits Analog Circuits android Arduino arm processor Assembly Languange Atmel Atom Size Audio Circuits augmented reality Automotive Circuits avr Battery Circuits Bicycle Gurad bluetooth Cable TV Circuits Cambridge University Camera Technology Circuit Boards Clipping And Clamping Circuits Clocking And Timer Circuits Computing contact lens Contact Us Form Contests Controller Circuit Conversion Circuits Counter Circuits Digital Electronics diy circuits Downloads EFY EFYTimes Electronic Books Electronic Components Electronic Locks And Keys Engineering Fan Circuits Filter Circuits Fire Alarm free Frequency Fun And Game Circuits future Google Hack n Mod Ham Radio Circuits heart rate monitoring High Voltage Circuits Home Circuits IC Guide ieee Industrial Circuits Infrared Instructables Inventions ipad lcd Led Circuits Light Related Lighting Circuits Medical Circuits Meter Clocks Microcontrollers Microprocessors Mini Projects modules Movie maker NatGeo Navigation Notice Optical Fiber PC Circuits PCB Boards Physics pnp transistor Power Supplies Printing Projects Programmer Project Ideas Projectors Protection circuits Proximity Detectors Radar Radio Circuits Radio Transmitters Raspberry Raspberry Pie Remote Circuits Retis Lab RFID Robot Cars Robotics Science Science Alert Security And Safety Sensor Circuits Servo Motors Smallest Smartwatches sms Software solar cell sound application Spectram Switch Technology News Telephone Related Television Related Test And Measurement Circuits Thermal Projects Tone generator circuits Touch Screen Tutorials Wearables Wi-Fi Wireless
Like us on Facebook
Follow us on Twitter
Recommend us on Google Plus
Subscribe me on RSS